hasemmike.blogg.se - Kong for r8500

KONG FOR R8500 HOW TO
KONG FOR R8500 INSTALL
KONG FOR R8500 UPDATE
KONG FOR R8500 SOFTWARE
KONG FOR R8500 PC

The Icom IC-R8500 -32K could be purchased by the Federal government or for export only.

The IC-R8500 was reviewed in the April 1997 issue of QST magazine. The R8500 is supplied with an AD-55 AC adapter or may be run from 12 VDC with the supplied OPC-023C DC cord. Other rear panel jacks include: IF Output (10.7 MHz), Remote Jack, AGC Out Jack, External Speaker and RS-232C (DB25) Jack. The rear panel features three separate antenna inputs (covering two ranges: 0.1-30 MHz SO239/RCA and 30-2000 MHz N). Attenuation may be set for 0, 10, 20 or 30 dB. Other refinements include: Noise Blanker, S and Center Tune Meter, RF Attenuator, LCD Dimmer, Clock-Timer, Record Jack and Recorder Activation Jack, Selectable AGC and Main Dial Tension adjustment. And what a memory system! 1000 channels are available organized in 20 banks of 40 channels, plus 100 skip channels and 100 Auto Write Memories. Direct keypad frequency entry is available.

In addition you can program your own tuning step (0.5-199.5 kHz). The R8500 employs a PLL circuit which provides tuning and readout resolution to an amazing 10 Hz. Separate band pass filters minimize cross modulation and provide high sensitivity in the 0.1 to 30 MHz range. Triple conversion and advanced RF circuits achieve an improved dynamic range of 107 dB and an intercept point of 27.5 dBm. The APF can select between two bandwidths and serves as a tone control in the FM mode and can also selectively boost signals in the CW mode. The IF shift effectively rejects nearby signals in the SSB modes. This receiver is equipped with IF Shift and Auto Peak Filter functions. Reception modes include: AM, LSB, USB, CW, FM-N and FM-W. The R8500 (and R9500) are clear exceptions to this rule, combining the performance of the popular HF IC-R75 and venerable VHF/UHF IC-R7100. Most wideband receivers tend to perform only modestly below 30 MHz. Covering 100 kHz to 1999.99 MHz, this receiver does cover it all and more importantly it does it well throughout this extraordinary range. The Icom IC-R8500 -32K government receiver produces performance, coverage and sophistication rarely seen in other models. Specifications | Accessories | Display | Rear Panel | Larger Image

KONG FOR R8500 PC

Note: Please remember to change your PC back to “Obtain an IP address automatically” and “Obtain DNS server address automatically”.Icom R8500 Wideband Receiver, Icom IC-R8500 Once this is done, the Power LED will turn solid and the wireless LEDs are lit. You will need to wait about 4 minutes for the router to finish storing firmware into its flash memory.

The firmware has been successfully uploaded.

You should see a pop up saying that “0 block retransmitted”.

Press PUT button on the Tftpd64 utility to perform the firmware upload.

It will start with an orange color and then start flashing.

Turn router OFF for 10 seconds and then turn it back ON.

Unplug all port connections from router except this PC.

For Local File, browse to the location of the downloaded firmware file and select it.

For Port field, enter port 69 (it is the default port number for TFTP).

For Host field, enter the default router IP (usually 192.168.1.1).

In the Server interfaces field, select the LAN adapter of your computer.

KONG FOR R8500 SOFTWARE

Now run the Tftpd64 software that was installed earlier and do the following:.

Select Use the following IP address and set the IP address information like below:.

Double-click Internet Protocol Version 4 (TCP/IPv4).

Right-click Ethernet and select Properties.

Right-click the Windows start button then select Network Connections.

KONG FOR R8500 HOW TO

Connect a PC wired to the router and set it to have a static IP address (example 192.168.1.10).įor Mac users, go to Beginner: How To Set Up A Static IP in Mac OS X and proceed to step 5.

KONG FOR R8500 INSTALL

Download and install the Tftpd64 software from: TFTP Clientįor Mac users, a free client can be downloaded here: Mac TFTP Client.

Make sure to extract the file from the zip folder.

Download and save the router’s firmware onto the desktop of your computer.

KONG FOR R8500 UPDATE

Device bricked after performing a FW update.

If you do not understand them, do not attempt this without contacting NETGEAR technical support. The instructions assume a basic level of networking competence. Note: The steps below show how to reload firmware onto a NETGEAR router that will not boot due to a corrupt firmware.